Mivec Owners Group
http://www.mivec.co.nz/forums/

Turbo 1600 Mivec
http://www.mivec.co.nz/forums/viewtopic.php?f=29&t=3408
Page 4 of 4

Author:  boostdummy [ 09 Aug 2007 05:00 ]
Post subject: 

nope not at all. engine has in stock rods and rod bolts.

The stock rods are prity good, The cast is not bad, could have a bit more triangulation on them but still it is not bad..

The some such was actually referring to a decompression plate..

Author:  renaldo [ 14 Aug 2007 04:00 ]
Post subject: 

Anyone really have first hand experience with these rods letting go at 10 psi?
I would really like to know, rather than finding out by trial and error. Where will i get upgraded rods and pistons from for the mivec, anyone has links?

Author:  Damian [ 14 Aug 2007 11:49 ]
Post subject: 

renaldo wrote:
Where will i get upgraded rods and pistons from for the mivec, anyone has links?


http://www.rpw.com.au

Author:  Sunlight [ 03 Sep 2007 09:08 ]
Post subject: 

I'd like to share a little bit of my 2nd Gen Mivec Turbo, this is the setup:

1) Sheepdog BOV
[img]http://www.garagetuned.com/mivecturbo/IMG_2657.jpg[/img]
2) 510cc Injectors
[img]http://www.garagetuned.com/mivecturbo/IMG_2603.jpg[/img]
3) E-manage Blue
4) Stock Block and Head
5) Bar and Plate Intercooler (28"x10"x2.5")
[img]http://www.garagetuned.com/mivecturbo/IMG_2648.jpg[/img]
6) T3 .42/.48
[img]http://www.garagetuned.com/mivecturbo/IMG_2613.jpg[/img]
[img]http://www.garagetuned.com/mivecturbo/IMG_2615.jpg[/img]

Dynoed at 166whp at 35wtq.

Image
[img]http://www.garagetuned.com/mivecturbo/IMG_2861.jpg[/img]
[img]http://www.garagetuned.com/mivecturbo/IMG_2864.jpg[/img]

Now running a T3 .60/.63, no dyno figures just yet. The setup has been running strong for 3 years now.[/img]

Author:  Kot [ 04 Sep 2007 00:01 ]
Post subject: 

mivec engine ιts made for n/a use ,if i will make my mirage in turbo conversion i will choose to install a 2.0l from evo :P but mivec point+turbo it will be a grazy sweet sound!!!!!!

Author:  jibong [ 21 Sep 2007 21:29 ]
Post subject: 

nice turbo header!!

Author:  fras [ 08 Jun 2017 01:08 ]
Post subject:  Re: Turbo 1600 Mivec

Thinking of doing a Gen2 Mivec, bolt on turbo... What do u guys think of this setup

Stock Gen2 Mivec mr
evo 6/7 td05 16g turbocharger (5 psi)
38mm wastegate
gen2 93T gsr injectors
intercooler/bov
piggy back ecu
straight 95 fuel or 92 with water/meth

can i use the mivec head gasket for that boost or do i need a 93T head gasket to lower compression?
is it safe to rev to 8200rpm on 5psi on that stock motor?

Author:  Demost [ 21 May 2019 00:16 ]
Post subject:  Re: Turbo 1600 Mivec

I see this is quite an old thread, but I wanted to weigh in here. I have a gen 2 mivec 1800 that I built using the 93 with the 92 head. I was running quad throttles etc etc a very high compression n/a motor that was making 125.kw. Well I decided to bolt a turbo on. I used the td05 with a 20g front wheel and the 10.5 rear. 3 inch exhaust straight through side piped. Std mivec intake manifold and t/b. The head is stock with Jun type 2 cams. Running E85, 13 psi boost it made 215kw at the wheels in 5th gear as the clutch was slipping. That's 288hp at the front wheels! It sounds so good revving at 8500!
Ill try and post a video.

Author:  Spetz [ 25 Jun 2019 00:42 ]
Post subject:  Re: Turbo 1600 Mivec

Sounds like a nice setup.
When does the turbo create fullboost by?

Page 4 of 4 All times are UTC + 12 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/